[version]
$Revision: 5 $
$Date: 26/09/08 10:13a $

[setup]
plottername=KNK ZingAir
manufacturer=Generic
page=600000,59055,1016
******PageX,PageY,Resolution
notes=
cut=0,0,0,0,0,0,1,0,0,0,0,369,-372,0,0,0,0,0,0,0,10,0,0,1
tile=0,0,0,0,0,0,0,0
move1=15,15,85,0,0,0,0,90,0,0,0,30,0,0,0,0,0,0,0,0,0,0,0,0,0,0,25
move2=10,10,85,0,0,0,0,90,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,0,0,0,0
move3=10,10,85,0,0,0,0,90,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
move4=10,10,85,0,0,0,0,90,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
moveLimit1=0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
moveLimit2=100,360,0,0,0,0,0,100,0,0,0,360,0,0,0,0,0,0,0,0,0,0,0,0,0,0
calculateW=TRUE
MaxVector=32000
Forced Jog=TRUE
generic=1
XYMoveAbs=1
ArcAbs=1
ArcSupport=1
regmarksdisallowed=0,0,0,1,1,1,0,0,1,1
cbccounter=1
CutByColor=0
DeviceLimits=600000,59055,1000
MachineIdNum=-1
SkipFileDialog=0
scale=1016,1016,1016
defscale=1016,1016,1016
MultiRes=1016
ResSel=0
setupplot=1,1
Origin=1
MaterialPosition=0
MaterialOrientation=0
XAdj=-50	
YAdj=1000
EndXMove=0
UseDriverCopies=0
mode=2
fnamecounter=1
// none,1pta,man,opos,mutoh,cornout,2pta,3pta,cornin,useprint,
OrigAdj=1

[MoveControl]
Variables=3
*Vn=Name,units,lowlimit,highlimit,command
V1=Velocity, ,1,38,VS%d
V2=Up Speed, ,1,38,US%d
V3=Force, ,1,160,!FS%d
velocityvar=1
velocityupvar=2
pressurevar=3


[Interrogation]
HardClip=;: ER,1000,99,41,(%*d,%*d,%*ld,%*ld,%*ld,%*ld,%*ld,%*ld,%*ld,%*ld,%ld,%ld
autogetpage=0
// Local jogging does not work when plotter is in remote
;Digitize=ED\r\n
;CurrentPos=~,1000,99,41,(%*d,%*d,%ld,%ld
;PlotterID=;: Q,100,30,13,%s

[Generic]
;AbsMove=PA
;RelMove=R
MoveUp=U%.0lf,%.0lf;
MoveDn=D%.0lf,%.0lf;
Tile=F%.0lf
AbsArc=CA%.0lf,%.0lf,%.2lf
RelArc=CA%.0lf,%.0lf,%.2lf
Pause=EL
;EndJob=|@ U0,0 U F U @
EndJob= @;
StartJob=ZG;PN1;PA;U0,0;
;Term=\r\n
;Term=;

[Jog]
init=SLN
end=SLF
DropTool=0
CutRegMarks=0

[Tool1]
ToolInit=
ToolEnd=
velocityvar=1
velocityupvar=2
pressurevar=3

[Tool2]
;ToolInit=

[Tool3]
ToolInit=
ToolEnd=

[Tool4]

[TOOLS]
*Max. Characters for Tool Name=10
*Tool Type: - Tangential (Steered) Knife=0
*           - Pen or Trailing Knife WITH PLOTTER OFFSET=1
*           - Pounce=2
*           - Trailing Knife WITH CADLINK OFFSET=3
Number Of Tools=4
Tool 1 Name=Knife
Tool 1 Type=1
Tool 2 Name=Pen
Tool 2 Type=1
Tool 3 Name=Pounce
Tool 3 Type=2
Tool 4 Name=Trailing
Tool 4 Type=3
Number Of Selected Tool=1
Tool 1 Check Boxes Data=0,0,0,0,0,0,0,0

[Trailing Blade]
*In order to initialize (proper alignment) a trailing blade, an initial
*blade correction cut is performed (NO=disable; YES=enable).
Initial Blade Correction=YES

[Resolution]
;Low=1
;Med=5
;High=25
;CutResBase=.0254
;ArcFitRes=.0254

[Port Setup]
Use DOS Device=0
Port=COM7:
PortType=0
Spool=0
qfullname=
HotFolder=
qport=-1
qname=
BufData=1
TXLumps=
Commset=57600,n,8,1,x
;commset=9600,n,8,1,p
;Use DOS Device=1
;TXThreshold=10000
;TransmitBufSize=10000
;ReceiveBufSize=1024
;handshaking=0,0,0,0,0,0,0,1,1,17,19,100,900,0,0
;ReportError=0xFFFF
[Control]
ControlID=94
ControlCheck=15932
[reg marks]
dontcut=0
[CraftRobo Reg Marks]
UsingRegMarks=0
[Default]
move1=15,15,85,0,0,0,0,90,0,0,0,30,0,0,0,0,0,0,0,0,0,0,0,0,0,0,25
move2=10,10,85,0,0,0,0,90,0,0,0,0,0,1,0,0,0,0,0,0,0,0,0,0,0,0,0
move3=10,10,85,0,0,0,0,90,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
move4=10,10,85,0,0,0,0,90,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0,0
[Materials]
m0=Default
NumMaterials=1
CurrMat=0
MatName=Default

[Jog]
init=SLN
end=SLF
DropTool=0
CutRegMarks=0
JogToRegMarks=1